
Metal Roofing in Lakeland and Central Florida
Metal roofing in Lakeland is a standing seam roof on a house, an exposed-fastener panel on a porch or a rural building, or a metal roof on a shop. True Roofers repairs and replaces those systems. Homeowners in Plant City have moved from shingles to standing seam. We do not name them. The Lakeland Google listing includes metal on commercial work.
License CCC1332725. 12+ years. 4.9 stars, 240+ reviews. Call (813) 800-1800. Lakeland office (863) 624-6590. Plant City (813) 743-4487.
Standing Seam and Exposed-Fastener Panels
Standing seam hides the fasteners in the seam. That is the system we install when a house is leaving shingles. Exposed-fastener panels, the screw-down roofs you see on porches, barns, and some Plant City rural houses, are a different repair. The screws and the washers are what fail. A standing-seam leak is usually a seam, a ridge, or a flashing, not a field of loose screws.
An estimate for one is not an estimate for the other. Ask which system is on the page before you compare two bids. Our November 2026 calculator, on the Central Florida replacement cost post, starts exposed-fastener metal at $14,500 for 2,000 square feet of measured roof surface. That figure is a starting price for that system, not a standing-seam quote and not a promise.
Standing Seam, the System People Ask About
Standing seam is the metal roof with raised ribs and no screw heads in the field of the panel. The panels lock or snap at the rib. Clips or a concealed fastener hold them to the deck. That is why a standing seam leak is almost never "tighten the screws." The water gets in at a seam that opened, at the ridge, at a pipe, or where the panel meets a wall.
On a house leaving shingles, this is the system we install when the owner wants metal and the HOA allows it. It is also the system that sits at the high end of the market band below. Oil-canning, the slight waviness you can see in a flat pan in hard sun, is a look some panels show. It is not, by itself, a leak. A leak is an open joint or a failed flashing, and that is what we photograph.
Metal Roof Repair
Metal roof repair in Florida is usually one of three things. On an exposed-fastener roof, the screws back out and the rubber washers crack, so water follows the fastener into the deck. The repair is a fastener and washer pass, plus any panel that has rusted through around the hole. On standing seam, the repair is the opened seam, the ridge cap, or the boot. On either system, a rust hole you can see through is past a washer.
We do not coat a rusted panel and call it repaired. If the panel is gone, that panel comes off. If the rust is a line across the slope, the repair conversation is over and you are looking at replacement.
Repair or Replacement
A metal repair is a resealed penetration, a replaced pipe boot, a run of bad flashing, or a screw-and-washer pass on an exposed-fastener roof that is otherwise sound. Replacement is the right call when the panels are rusted through, the seams have opened across a slope, or the owner is done with shingles and wants standing seam on a new deck.
We photograph what we find. We do not file the claim and we do not adjust it. Read is a metal roof better than shingles in Florida if you are still choosing, then book a roof inspection so the answer is about your roof.
Market Ranges, Not Our Price List
As a general Central Florida market range, not a True Roofers price, a metal roof on a 2,000 to 2,500 square foot house often falls between $12,000 and $30,000 and up. Standing seam sits at the high end. Exposed-fastener panels sit lower. Pitch, tear-off, and decking move it more than the color.
Your number is the written price after the inspection. Call (813) 800-1800.
People searching metal roof cost in Florida are usually comparing a house, not a warehouse. Use the house band above for that question. A Lakeland shop or warehouse is priced from the building: panel length, the curbs, and whether the crew is working over an open store. Metal roofing in Lakeland, for a house, starts at the office on Badger Rd. The commercial metal jobs are on the commercial page.
| System | Where we see it | Market note |
|---|---|---|
| Standing seam | Houses leaving shingles | High end of the $12,000 to $30,000 band, and above it on complex roofs |
| Exposed-fastener panels | Porches, rural houses, some shops | Lower than standing seam. Fasteners and washers are the usual repair |
| Commercial metal | Lakeland warehouses and shops | Quoted from the building, not from a house square-foot band |
General market range, not True Roofers prices. The calculator starting price for exposed-fastener metal is on the Central Florida replacement cost post and applies only to that example.
Lakeland, Plant City, and the Commercial Shops
Lakeland comes first. The office is 2829 Badger Rd #19, (863) 624-6590. Plant City HQ is 4000 N Frontage Rd, (813) 743-4487. Commercial metal on a warehouse is a different crew plan than a house. That work also lives on commercial roofing.
If the metal roof is flat, or it is TPO and someone called it metal because it is not shingle, use the flat roof repair page. A standing seam roof and a TPO membrane are not the same repair.
Metal Roofing Across Central Florida
Local crews dispatched from Lakeland, Plant City, and Auburndale: